The Avenger 460 is a great machine for smaller jobs or homes, offices and rooms. It is a true planetary grinder with
5.5 Hp counter-rotating grinding heads. All gear construction and power to the three grinding heads and the rotating drum. Available in 110 volt and 220 volt single phase input
on the same machine. The size and weight allow for easy loading and unloading at the jobsite or to carry up to a mezzanine or landing. The Avenger 460 is very versatile, and can be used for coatings removal, grinding and polishing.
American Made Controls
This machine is
single Phase input power, but is a full three phase machine internally with variable speed and forward and reverse, this also means that this machine is vastly more reliable then the regular single phase machines from competitive sources.
Feature:
Specifications:
Motor
Single Phase input - Three
Phase IEC 5.5 Hp on board
Voltage
110 volt or 208-240 Volt Single Phase
Weight
350Lb plus any Weights added
Working Width
19 inches (480mm)
Speed
300-1200 RPM on the grinding head
Water Tank
6.6 gal (25 liters)
Abrasive Plates
Three 8" counter-rotating grinding heads on rotating drum.
All Gear Design
The 460 is all gear design with drive to each of the three flex heads
as well as power to the drum for the highest production rate in its
size. Click picture to see inside planetary system.
Magnetic Instant-Change Tool System.
The Avenger 460 comes with the Magnetic Instant-change tool mounting system. All you will need to purchase is the diamond tools you will need for your particular project. The system can mount scrapper tools ,regular metal trapezoid tools, and velcro mount tools.
Water and Dust Resistant Electronics
The Motor controller on all Avenger machines are indoor and outdoor rated
for harsh environments with water and dust protection. You get maximum cooling when it is hot
because the cooling fins on the back are always open to the air not sealed in a
cabinet, and no entry of dust into the electronics cavity is possible. USA MADE
Control Head
The Avenger 460 has all the features of much larger machines, such as forward and reverse directions on the grinding heads. This allows you to run directional tools such as scrapper tools to remove epoxy and glue. Most diamond tools do not have a direction so you can run those either way. The 460 also has variable speed to grind rough floors by slowing down the grinding heads to keep them from bouncing which will stop them from cutting. By speeding up the grinding heads you can polish and burnish the floor with the proper tooling. Variable speed also allows you to work on marble and granite floors.
Ratcheting Handle
You can instantly adjust the handle to be more comfortable, or to tip the machine over or to store the handle outr of the way.
One squeeze of the lever and move is to position.
PRODUCTION RATES
sqf per hr m² per hr
Concrete Grind 1 step
350-550
35 -55
Terrazzo Grind 1 step
90-130
10 -15
Glue Removal 1 step
350-0500
35 - 50
Paint Removal 1 step
350-500
35 - 50
Marble Polishing 5 steps
70-110
5 - 10
* Production numbers may vary according to surface conditions, diamonds used, equipment operator, etc.
Vacuums
Because it is important to use a functional Hepa vacuum if you are going to grind dry, Levetec has a supply of low cost HEPA filter vacuums to do the job. Filtration is an enormous issue when it comes to industrial vacuum cleaners. After all, if you take the time to vacuum an area, the last thing you want is the same material that you just vacuumed to be exhausted right back into the atmosphere. Depending on what you're collecting, the dust or debris may be hazardous to your product finish, or even your health. We, at Levetec, realize the importance of ultra-efficient filtration systems and put our guarantee on every industrial vacuum cleaner we sell.
Metal Diamond Tools
To grind floors effectively it is necessary to use metal tools to grind down through the cap and leave a substrate that is ready to coat, seal or polish. Click on the picture to see the metal diamond tooling.
Resin Diamond Tools
To bring a floor up to a high shine it is necessary to use
Resin tools to polish the substrate to the look you seek or to coat,
seal or polish. Click on the picture to see the Resin diamond tooling.
Contact
Levetec
